CISCO EIGRP COMMAND AND CONFIGURATION HANDBOOK PDF

| | 0 Comments

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Tojabei Memuro
Country: Cape Verde
Language: English (Spanish)
Genre: Sex
Published (Last): 19 March 2017
Pages: 113
PDF File Size: 5.55 Mb
ePub File Size: 2.69 Mb
ISBN: 702-5-56583-196-5
Downloads: 54755
Price: Free* [*Free Regsitration Required]
Uploader: Vugul

Austin config-router network Without it, an administrative distance of 5 is automatically applied to the summary route. Houston config-if clock rate Sets the clock rate. Router config-router maximum-paths 6. When you enable EIGRPv6 on an interface using the ipv6 eigrp asn command, the router would start discovering neighbors off that interface.

NOTE If a path is not a feasible successor, it is not used in load balancing. Router config-router distribute-list 1 in. The rest of the configuration simply enables EIGRPv6 on all interfaces using the ASN to associate with the interface, using the ipv6 eigrp asn command.

For instance, you could have two routers advertise the same network— HULL config-router distribute-list 10 out Or. See All Related Articles. Austin config-keychain-key key-string tower. Houston config exit Returns to privileged mode. Return to Beginning Previous Section. With the maximum-paths router configuration command, up to 32 equal-cost entries can be in the routing table for the same destination. The Hello messages enable routers to discover each other and also contain some parameters.

  DJURO SUSNJIC PDF

Austin config-keychain-key send-lifetime The show ipv6 eigrp topology command provides more detailed topology information about the subnet, as shown below:.

However, this omission means that EIGRPv6 is not enabled on the interface, and therefore the router will not advertise about that connected subnet. Houston config-router eigrp log-neighbor-changes Changes with neighbors will be displayed.

The configuration settings are made with the maximum-paths and variance commands in EIGRPv6 router configuration mode, reached with the ipv6 router eigrp command.

NOTE Setting the maximum-path to 1 disables load balancing. Austin config-router eigrp log-neighbor-changes Changes with neighbors will be displayed.

EIGRP Configuration| Step By Step Guide

Austin config-router no auto-summary. Identifies a key chain name, which must match the name configured in interface configuration mode. HULL config access-list 10 deny Austin copy running-config startup-config.

Set interface bandwidth and delay to influence metric calculation interface configuration mode.

Topology entry for Houston config-keychain-key key-string tower. You may use the show ipv6 eigrp interfaces command to verify if EIGRPv6 has been enabled on correct interfaces:. Austin config-router eigrp log-neighbor-changes. The subnet has one successor, which has an FD feasible distance of cnfiguration If the parameters do match, the two routers become neighbors hanndbook each router adds the other to its EIGRPv6 neighbor table, as listed with the show ipv6 eigrp neighbors command.

EIGRP automatically summarizes networks at the classful boundary.

No neighbor adjacency will be formed. Houston config-if ip authentication mode eigrp md5.

  AGAM SUTRAS PDF

EIGRP Configuration| Step By Step Guide

Please keep in mind that even if only one of the two routers has a passive interface, the neighbor relationship will fail. Router config-router passive-interface default Prevents handook sending hanrbook hello packets out all interfaces. As a result, networks Houston config-if ip address The FS feasible successor is a route that meets the feasibility condition and can potentially become the successor route if the successor route fails.

Houston config-if no shutdown Enables the interface.

Austin config-router key chain susannah Identifies a key chain name, which must match the name configured in interface configuration mode. EIGRPv6 then exchange messages allowing the routers to discover neighbors, form neighbor relationships, and finally advertise subnets along with the metric components for each route. However, if the parameters do not match, the two routers do not become neighbors and do not add each other to the EIGRPv6 neighbor table, listed by the show ipv6 eigrp neighbors command.

About Affiliates Cisco Systems, Inc. It commanx be applied to ekgrp type 2 and external type 1 routes but not to intra-area and interarea routes. An administrative distance of 75 is assigned to this summary route.